Carrito
No hay más artículos en su carrito
KINGSTON MEMORIA 8GB DDR4 2666 MHZ CL19
MEMORIA - DDR4-2600 - KINGSTON KVR26N19S6-8 - KINGSTON MEMORIA 8GB DDR4 2666 MHZ CL19
KVR26N19S6/8
8GB 1Rx16 1G x 64-Bit PC4-2666
CL19 288-Pin DIMM
Continued >>
FEATURES
This document describes ValueRAM's KVR26N19S6/8 is a 1G x
64-bit (4GB) DDR4-2666 CL19 SDRAM (Synchronous DRAM),
1Rx16, memory module, based on four 1G x 16-bit FBGA
components. The SPD is programmed to JEDEC standard
latency DDR4-2666 timing of 19-19-19 at 1.2V. Each 288-pin
DIMM uses gold contact fingers. The electrical and mechanical
specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
UL Rating
Operating Temperature
Storage Temperature
19 cycles
45.75ns(min.)
350ns(min.)
32ns(min.)
94 V - 0
0o
C to +85o
C
-55o
C to +100o
C
Power Supply: VDD = 1.2V Typical
VDDQ = 1.2V Typical
VPP = 2.5V Typical
VDDSPD = 2.2V to 3.6V
Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
Low-power auto self refresh (LPASR)
Data bus inversion (DBI) for data bus
On-die VREFDQ generation and calibration
Single-rank
On-board I2 serial presence-detect (SPD) EEPROM
8 internal banks; 2 groups of 4 banks each
Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
Selectable BC4 or BL8 on-the-fly (OTF)
Fly-by topology
Terminated control command and address bus
PCB: Height 1.23 (31.25mm)
RoHS Compliant and Halogen-Free
https://www.kingston.com/dataSheets/KVR26N19S6_8.pdf
8GB 1Rx16 1G x 64-Bit PC4-2666
CL19 288-Pin DIMM
Continued >>
FEATURES
This document describes ValueRAM's KVR26N19S6/8 is a 1G x
64-bit (4GB) DDR4-2666 CL19 SDRAM (Synchronous DRAM),
1Rx16, memory module, based on four 1G x 16-bit FBGA
components. The SPD is programmed to JEDEC standard
latency DDR4-2666 timing of 19-19-19 at 1.2V. Each 288-pin
DIMM uses gold contact fingers. The electrical and mechanical
specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
UL Rating
Operating Temperature
Storage Temperature
19 cycles
45.75ns(min.)
350ns(min.)
32ns(min.)
94 V - 0
0o
C to +85o
C
-55o
C to +100o
C
Power Supply: VDD = 1.2V Typical
VDDQ = 1.2V Typical
VPP = 2.5V Typical
VDDSPD = 2.2V to 3.6V
Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
Low-power auto self refresh (LPASR)
Data bus inversion (DBI) for data bus
On-die VREFDQ generation and calibration
Single-rank
On-board I2 serial presence-detect (SPD) EEPROM
8 internal banks; 2 groups of 4 banks each
Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
Selectable BC4 or BL8 on-the-fly (OTF)
Fly-by topology
Terminated control command and address bus
PCB: Height 1.23 (31.25mm)
RoHS Compliant and Halogen-Free
https://www.kingston.com/dataSheets/KVR26N19S6_8.pdf
No reviews