Carrito
No hay más artículos en su carrito
KINGSTON MEMORIA FURY BEAST 8GB DDR3 1600Mhz
MEMORIA - DDR3-1600 - KINGSTON KF316C10B-8 - KINGSTON MEMORIA FURY BEAST 8GB DDR3 1600Mhz
KF316C10B/8
8GB 1G x 64-Bit
DDR3-1600 CL10 240-Pin DIMM
Continued >>
FEATURES
FURY KF316C10B/8 is a 1G x 64-bit (8GB) DDR3-1600 CL10
SDRAM (Synchronous DRAM) 2Rx8, memory module, based on
sixteen 512M x 8-bit FBGA components per module. Each module
has been tested to run at DDR3-1600 at a low latency timing of
10-10-10 at 1.5V. Additional timing parameters are shown in the
Plug-N-Play (PnP) Timing Parameters section below. Each 240-pin
DIMM uses gold contact fingers. The JEDEC standard
electrical and mechanical specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
UL Rating
Operating Temperature
Storage Temperature
10 cycles
48.125ns(min.)
260ns(min.)
37.5ns(min.)
94 V - 0
0o
C to +85o
C
-55o
C to +100o
C
FACTORY TIMING PARAMETERS
Default (Plug N Play): DDR3-1600 CL10-10-10 @ 1.5V
DDR3-1333 CL9-9-9 @ 1.5V
DDR3-1066 CL7-7-7 @ 1.5V
JEDEC standard 1.5V Power Supply
VDDQ = 1.5V
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address 000 only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
Height 1.338 (34mm) w/heatsink
Document No. 4810128A 07/12/21 Page 1 kingston.com
Memory Module Specifications
Note: The PnP feature offers a range of speed and timing options to support
the widest variety of processors and chipsets. Your maximum speed will
be determined by your BIOS.
MODULE DIMENSIONS
MODULE WITH HEAT SPREADER
continued
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published FURY memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
https://www.kingston.com/dataSheets/KF316C10B_8.pdf
8GB 1G x 64-Bit
DDR3-1600 CL10 240-Pin DIMM
Continued >>
FEATURES
FURY KF316C10B/8 is a 1G x 64-bit (8GB) DDR3-1600 CL10
SDRAM (Synchronous DRAM) 2Rx8, memory module, based on
sixteen 512M x 8-bit FBGA components per module. Each module
has been tested to run at DDR3-1600 at a low latency timing of
10-10-10 at 1.5V. Additional timing parameters are shown in the
Plug-N-Play (PnP) Timing Parameters section below. Each 240-pin
DIMM uses gold contact fingers. The JEDEC standard
electrical and mechanical specifications are as follows:
CL(IDD)
Row Cycle Time (tRCmin)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
UL Rating
Operating Temperature
Storage Temperature
10 cycles
48.125ns(min.)
260ns(min.)
37.5ns(min.)
94 V - 0
0o
C to +85o
C
-55o
C to +100o
C
FACTORY TIMING PARAMETERS
Default (Plug N Play): DDR3-1600 CL10-10-10 @ 1.5V
DDR3-1333 CL9-9-9 @ 1.5V
DDR3-1066 CL7-7-7 @ 1.5V
JEDEC standard 1.5V Power Supply
VDDQ = 1.5V
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address 000 only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
Asynchronous Reset
Height 1.338 (34mm) w/heatsink
Document No. 4810128A 07/12/21 Page 1 kingston.com
Memory Module Specifications
Note: The PnP feature offers a range of speed and timing options to support
the widest variety of processors and chipsets. Your maximum speed will
be determined by your BIOS.
MODULE DIMENSIONS
MODULE WITH HEAT SPREADER
continued
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published FURY memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
https://www.kingston.com/dataSheets/KF316C10B_8.pdf
No reviews